Name: 1st TCT Workshop
Start: 2015-10-05T13:00:00+02:00
End: 2015-10-06T17:00:00+02:00
Location: DESY Hamburg

1st TCT Workshop

from Monday, October 5, 2015 (1:00 PM) to Tuesday, October 6, 2015 (5:00 PM)

Monday, October 5, 2015

1:00 PM

1:00 PM - 1:30 PM
Room: SR3
1:30 PM
1:30 PM - 1:35 PM
Room: SR3
Contributions

1:30 PM Welcome - Hendrik Jansen (DESY)
1:35 PM
1:35 PM - 3:40 PM
Room: SR3
Contributions

1:35 PM Introduction to TCT and edge-TCT workshop - Susanne Kuehn (University of Freiburg) Susanne Kuehn (Univ. Freiburg)

1:50 PM Hardware description: Particulars system - Gregor Kramberger (Jozef Stefan Institute) Marko Zavrtanik (Jozef Stefan Institute)

2:10 PM Harware description: CERN system - Christian Gallrapp (CERN)

2:30 PM PCBs and mounts for different sensors: diode, strip sensors, CMOS - Hendrik Jansen (DESY)

2:40 PM Discussion on setups

2:55 PM Sensor preparation for edge, backside illumination - Sven Wonsak (University of Liverpool)

3:05 PM DAQ + Software operation for particulars - Gregor Kramberger (Jozef Stefan Institute)

3:20 PM Introduction to finding of focus - Gregor kramberger (Jozef Stefan Institute) Hendrik Jansen (DESY)
3:40 PM Coffee Break
Coffee Break
3:40 PM - 4:00 PM
4:00 PM
4:00 PM - 6:00 PM
Room: Lab2/Lab4
Contributions

4:00 PM Cabling, DAQ and software operation of particulars system

5:00 PM Sensor preparation
7:30 PM Dinner at Mamma Mia
Dinner at Mamma Mia
7:30 PM - 9:30 PM
Barnerstraße 42, 22765 Hamburg
Tuesday, October 6, 2015
9:00 AM
9:00 AM - 10:45 AM
Room: SR1
Contributions

9:00 AM Theoretical background for measurements - Gregor Kramberger (Jozef Stefan Institute) Marko Zavrtanik (Jozef Stefan Institute)

9:20 AM Discussion and Questions

9:30 AM Simulation from Torino - Nicolo Cartiglia (University of Turin and INFN)

9:50 AM Simulation from Ljubljana - Gregor Kramberger (Jozef Stefan Institute) Marko Zavrtanik (Jozef Stefan Institute)

10:10 AM Simulation with TRACS - Marcos Fernandes Garcia

10:25 AM Common code - Hendrik Jansen (DESY)
10:45 AM Tea Break
Tea Break
10:45 AM - 11:00 AM
11:00 AM
11:00 AM - 12:30 PM
Room: Lab2
Contributions

11:00 AM Measurement of edge pulse

11:30 AM Readout board: DRS, Oscilloscope

12:00 PM Temperature control and stability: PID controller
12:30 PM Lunch Break
Lunch Break
12:30 PM - 2:00 PM
2:00 PM
2:00 PM - 4:00 PM
Room: SR1
Contributions

2:00 PM Do's and Don'ts - Sven Wonsak (University of Liverpool)

2:20 PM Discussion & Questions

2:40 PM Discussion on common code development - Hendrik Jansen (DESY)